Kennedy Rainbow Cell

Kennedy Rainbow Cell electrolysis chemistry demonstration initial setup aerial view
Initial Kennedy Rainbow Cell setup

Demonstrate electrolysis with an electrolytic cell in a petri dish.

Materials

  • 1 × Large petri dish
  • 1 × DC Power pack
  • ~50 mL Distilled water dH2O(l)
  • ~3 g potassium nitrate powder KNO3(s)
  • 2 × Graphite electrodes
  • 2 × Wires with crocodile clips
  • 1 × Clamp and stand
  • 1 × Very strong static magnet
  • 1 × Roll of sticky tape (any type)
  • ~10 drops of universal indicator
  • ~50 mL dilute HNO3(aq)
  • ~50 mL dilute KOH(aq)
  • 1 × Spatula

Method

  1. Place petri dish on clean, light-coloured bench and add distilled water until it is two thirds full
  2. Add ~10 drops of universal indicator and observe the colour.
    Q: What pH is the distilled water? (You’ll be surprised!)
    Q: Why is/isn’t the colour green?
  3. Add ~3 g of potassium nitrate to the petri dish and stir using a spatula until completely dissolved
  4. Adjust the pH of the distilled water carefully using the nitric acid and potassium hydroxide as required. Try to make the universal indicator colour green (as pictured) ~pH 7
  5. Attach one electrode to each of two wires using crocodile clips
  6. Dip each graphite electrode into the green solution at opposite sides of the petri dish. Hold these electrodes (and wires) in position by in position by sticky-taping each wire to the surface of the workbench
  7. Demonstrate the strength of the magnet by attaching it to the clamp. Carefully, clamp the magnet into the clamp and position the magnet 2 mm above the surface of the green solution
  8. Ensuring the power is turned off, very carefully, attach the wires to the DC power pack according to the manufacturer’s instructions
  9. Turn the voltage to zero (or very low) and turn on the power pack
  10. Turn the voltage up slowly (12 volts worked well) and observe any changes you might see in the Kennedy Rainbow Cell

Extensions

  • Turn off the power pack and stir the solution. Explain why the colour goes back to being green. (If it’s not green, explain that, too!)
  • Turn the magnet upside-down (TURN OFF THE POWER FIRST)
  • Reverse the polarity of the wires
  • Use AC current instead of DC
  • Use different indicators
  • Why would using NaCl(aq) be dangerous in this cell?
  • How can you maximise the swirling?
  • How can you make this experiment much more epic?

Click to download Kennedy Rainbow Cell worksheet (PDF)

Safety considerations

  • Make your own risk assessment before carrying out this experiment
  • The strong magnet is capable of attracting both wires to itself. Don’t be touching the exposed parts of the crocodile clips when this happens. If this does happen, immediately turn off the power pack and fix the problem. Secure the wires with more tape. Don’t touch the electrodes while the Cell is operating.
  • Don’t use chloride salts or hydrochloric acid in this experiment. The voltages involved can cause the production of toxic chlorine gas if sodium chloride is used. Use nitric acid and potassium nitrate instead.
  • Make sure the wires don’t touch each other.
  • Again, make your own risk assessment before carrying out this experiment

Video

Disclaimer

This cell is potentially dangerous. I accept no responsibility for and loss, damage or injury caused by the operation of a Kennedy Rainbow Cell. If you’re under 18, always get adult permission before you make this type of cell.

Talk to me

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s